HP HP0-P10인증시험패스에는 많은 방법이 있습니다. 먼저 많은 시간을 투자하고 신경을 써서 전문적으로 과련 지식을 터득한다거나; 아니면 적은 시간투자와 적은 돈을 들여 ITExamDump의 인증시험덤프를 구매하는 방법 등이 있습니다.
HP인증HP0-P10시험은 현재 치열한 IT경쟁 속에서 열기는 더욱더 뜨겁습니다. 응시자들도 더욱더 많습니다. 하지만 난이도난 전혀 낮아지지 않고 이지도 어려운 시험입니다. 어쨌든 개인적인 지식 장악도 나 정보기술 등을 테스트하는 시험입니다. 보통은HP인증HP0-P10시험을 넘기 위해서는 많은 시간과 신경이 필요합니다.
시험 번호/코드: HP0-P10
시험 이름: HP (HP Integrity Server Multi-OS Installation and Deployment)
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 147 문항
업데이트: 2013-09-26
ITExamDump의 HP인증HP0-P10시험대비덤프는 실제시험문제 출제경향을 충분히 연구하여 제작한 완벽한 결과물입니다.실제시험문제가 바뀌면 덤프를 제일 빠른 시일내에 업데이트하도록 하기에 한번 구매하시면 1년동안 항상 가장 최신의HP인증HP0-P10시험덤프자료를 제공받을수 있습니다.
ITExamDump 에서는 IT인증시험에 대비한 퍼펙트한HP 인증HP0-P10덤프를 제공해드립니다. 시험공부할 시간이 충족하지 않은 분들은ITExamDump 에서 제공해드리는HP 인증HP0-P10덤프로 시험준비를 하시면 자격증 취득이 쉬워집니다. 덤프를 구매하시면 일년무료 업데이트서비스도 받을수 있습니다.
HP0-P10 덤프무료샘플다운로드하기: http://www.itexamdump.com/HP0-P10.html
NO.1 The diagnostic panel on an Integrity rx4640 shows a fan failure. What information on the Management
Processor (MP) shows you when the fan failed?
A. MP:CM> PS
B. MP:CM> SS
C. MP> SL --> L - Live Events
D. MP> SL --> E - System Event
Answer: D
HP덤프 HP0-P10 HP0-P10 HP0-P10
NO.2 What is the difference between a Machine Check Abort (MCA) and a Transfer of Control (TOC)?
A. An MCA is a software dump; a TOC is a hardware register dump.
B. An MCA is a hardware register dump; a TOC initiates a software dump.
C. An MCA dump is for Windows systems; a TOC is for HP-UX systems.
D. An MCA dump is for HP-UX systems; a TOC is for Windows systems.
Answer: B
HP HP0-P10시험문제 HP0-P10 HP0-P10
NO.3 Which capability does the Management Processor (MP) in the Integrity rx2620 server provide?
A. offline hardware monitoring
B. hardware administration and management
C. remote HP-UX operating system installation
D. remote monitoring of server room conditions
Answer: B
HP HP0-P10 HP0-P10시험문제 HP0-P10
NO.4 You want to load new firmware for the Management Processor (MP). Which command do you use to
verify a proper connection to an FTP server?
A. xd
B. bin
C. scp
D. xu
Answer: A
HP dump HP0-P10인증 HP0-P10 dump
NO.5 What does an amber blinking System LED on an Integrity rx2620 indicate?
A. System is in error state
B. Remote access is enabled
C. A system warning
D. Management Processor is powered off
Answer: C
HP HP0-P10자료 HP0-P10 HP0-P10
NO.6 The system is not responding normally. You have access to the Management Processor (MP). Which
command do you use to cycle the power?
A. ps
B. pc
C. rs
D. co
Answer: B
HP인증 HP0-P10 pdf HP0-P10최신덤프 HP0-P10
NO.7 An Integrity rx2620 server with Windows Server 2003 is running terminal services but has stopped
responding. Which MP command do you use to shut down gracefully and power off the server?
A. rs -g
B. pc -g
C. rs -off
D. pc -off
Answer: B
HP HP0-P10덤프 HP0-P10 HP0-P10
NO.8 Where is the diagnostic panel on an Integrity rx4640 server located?
A. top
B. front
C. back
D. left side
E. right side
Answer: A
HP pdf HP0-P10 dumps HP0-P10인증 HP0-P10 dump HP0-P10
NO.9 In a Linux environment, what is one of the components used to manage highly available solutions
offered by Virtual Server Environment (VSE)?
A. HP Workload Manager
B. HP OpenView Node Manager
C. HP Global Workload Manager
D. Performance Management Pack
Answer: C
HP기출문제 HP0-P10 HP0-P10덤프 HP0-P10 HP0-P10
NO.10 After you replace a memory module on an Integrity server, how do you clear the entries in the Page
Deallocation Table (PDT)?
A. Interrupt the boot, go to the Service Menu and enter pdt clear.
B. Interrupt the boot, go to the EFI shell, and then enter pdt clear.
C. Interrupt the boot, enter the MP:CM> CL command, and choose PDT.
D. After reboot, the system automatically deletes entries in the PDT without user input.
Answer: B
HP자격증 HP0-P10자격증 HP0-P10 HP0-P10 dump
NO.11 Which methods of accessing the Offline Diagnostics Environment (ODE) utilities does HP recommend?
(Select two.)
A. from the HP service partition
B. from the EFI Boot Menu
C. from the MP command menu
D. from the operating system disk
E. from the Offline Diagnostic Utility CD
Answer: AE
HP HP0-P10 HP0-P10 HP0-P10최신덤프 HP0-P10기출문제
NO.12 You just installed an Integrity rx2620 server. How do you set the MP and system times?
A. Use the MP date command to set time and date.
B. The time will be set automatically during system boot.
C. Use the EFI shell command time to set time and date of the MP.
D. Use the MP date command to set the date, and use the MP time command to set the time.
Answer: C
HP HP0-P10시험문제 HP0-P10자격증 HP0-P10 dump HP0-P10자격증 HP0-P10
NO.13 Where does HP OpenVMS store all error information?
A. /var/adm/syslog/syslog.log
B. SYS$ERRLOG:SYSTEM.LOG
C. SYS$ERRORLOG:ERRLOG.SYS
D. SYS$MANAGER:OPERATOR.LOG
Answer: C
HP HP0-P10 HP0-P10덤프 HP0-P10
NO.14 How can you access the UUID on an entry-level HP Integrity server? (Select two.)
A. The UUID is written on the system information label of the server.
B. At the EFI Boot Manager menu, access the EFI Shell; then enter info sys.
C. At the Management Processor (MP) main menu, go to the Command Menu and enter id.
D. At the EFI Boot Manager menu, access the System Configuration menu and select System UUID.
E. If you access the EFI Boot Manager menu using integrated Lights-Out (iLO), the UUID displays
automatically.
Answer: AB
HP HP0-P10최신덤프 HP0-P10 pdf HP0-P10자료 HP0-P10 dumps
NO.15 You need to perform a maintenance task on a Management Processor module. Which command
displays a list of connected users?
A. who
B. list
C. usmgr
D. show user
Answer: A
HP HP0-P10 HP0-P10
NO.16 You have run an Offline Diagnostics Environment (ODE) utility. What should you do before booting
the operating system or running any non-ODE utility?
A. Reset the system at the MP:CM> prompt.
B. Use the MP:CM> poff command to power off the DC voltage.
C. Reset the system at the EFI shell prompt and disconnect the AC power for one minute.
D. Reset the system at the EFI shell prompt, use the MP:CM> pc command to power off DC voltage, and
disconnect the AC power for one minute.
Answer: A
HP HP0-P10 HP0-P10 HP0-P10기출문제 HP0-P10인증
NO.17 Which command do you use in the EFI Shell to verify that an Integrity rx4640 server has the latest
firmware?
A. openinfo fw
B. info fw
C. ver fw
D. sysrev
Answer: B
HP기출문제 HP0-P10자격증 HP0-P10 HP0-P10덤프
NO.18 You replaced failed hardware in an HP Integrity server. Which steps should you perform to ensure
that the system is operational?
A. Verify that the replaced hardware is visible in the EFI Shell, and that the Diagnostic LEDs are clear.
B. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded.
C. From the EFI Shell, boot the system. From within the operating system, confirm that the replaced
hardware is functioning and verify the correct status of the Diagnostic LEDs.
D. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded. Then boot the system and confirm that the replaced hardware is functioning.
Answer: D
HP HP0-P10 HP0-P10시험문제 HP0-P10자료
NO.19 You have limited access to the Management Processor (MP), but you have full access to the system
Baseboard Management Console (BMC). Which command do you issue in the BMC Command Line
Interface (CLI) to power off the system hardware?
A. cli> p 0
B. cli> rs 1
C. cli> pc 0
D. cli> loc 0
Answer: A
HP HP0-P10 dump HP0-P10 HP0-P10
NO.20 Which front panel LEDs on an Integrity rx2620 can indicate an error?
A. Locator LED and System LED
B. Power LED and Diagnostic LEDs
C. System LED and Diagnostic LEDs
D. Diagnostic LEDs and Locator LED
Answer: C
HP자료 HP0-P10시험문제 HP0-P10 HP0-P10 HP0-P10기출문제
NO.21 Which Offline Diagnostics Environment (ODE) utility should you use to test processors on an Integrity
server?
A. WDIAG
B. IA64DIAG
C. CPUDIAG
D. PROCDIAG
Answer: C
HP dumps HP0-P10시험문제 HP0-P10 dumps
NO.22 You are managing an Integrity rx2620 server that is located in a remote office. Which Management
Processor (MP) console command do you use to gather the state of the system and LEDs?
A. LED
B. VFP
C. ERRDUMP D. SYSSTAT
Answer: B
HP HP0-P10기출문제 HP0-P10 HP0-P10
NO.23 The rx3600 and rx6600 have LEDs which show the FRU Health status. How can you view the state of
these LEDs remotely?
A. From the MP main menu, select VFP
B. From the MP main menu, select SL
C. From the MP main menu, select CM, then LS
D. From the MP main menu, select CM, then DF
Answer: A
HP dumps HP0-P10 HP0-P10덤프 HP0-P10
NO.24 Which Offline Diagnostics Environment (ODE) utility should you use to test an HP Tachyon XL2 Fibre
Channel card?
A. IODIAG
B. FCDIAG
C. PERFVER
D. FCFUPDATE
Answer: A
HP dump HP0-P10 HP0-P10인증
NO.25 How can you determine the firmware version that is running on an HP Integrity system? (Select two.)
A. At the EFI Boot Manager menu, open the EFI shell and enter info fw.
B. At the MP main menu, open the Command Menu (cm) and enter firmware.
C. At the EFI Boot Manager menu, go to the Firmware menu and select Version.
D. At the EFI Boot Manager menu, go to the Firmware Configuration menu and select Version.
E. If you access the EFI Boot Manager menu using iLO, the firmware versions display automatically.
Answer: AE
HP HP0-P10덤프 HP0-P10자격증
NO.26 Which Management Processor (MP) command displays the physical location information of the
system?
A. SI
B. ID
C. LOC
D. SO
Answer: B
HP HP0-P10 HP0-P10 HP0-P10 HP0-P10
NO.27 Which command in the iLO 2 controls access permissions for an Integrity rx6600 server?
A. PS
B. SO
C. PC
D. SD
Answer: B
HP최신덤프 HP0-P10 HP0-P10인증 HP0-P10 dumps HP0-P10덤프 HP0-P10
NO.28 Which Offline Diagnostics Environment (ODE) utility should you use to test the memory of an Integrity
server?
A. MAPPER
B. SYSDIAG
C. MEMDIAG
D. DIMMDIAG
Answer: C
HP pdf HP0-P10최신덤프 HP0-P10덤프 HP0-P10기출문제 HP0-P10 dump
NO.29 You must back up all your Integrity server NVRAM configurations. Which backup utility is available for
download that can be used in the EFI shell?
A. bcfg
B. getmtc
C. nvrambkp
D. bcknvram
Answer: C
HP HP0-P10 HP0-P10 HP0-P10기출문제
NO.30 From the EFI Boot Manager, how can you get information about the installed memory DIMMs?
A. Go to the EFI Shell and enter: info mem
B. It is not possible to get the information offline.
C. The information displays automatically at the EFI Boot Manager menu.
D. Go to the System Configuration menu and choose Memory Configuration.
Answer: A
HP HP0-P10자료 HP0-P10최신덤프 HP0-P10최신덤프
ITexamdump의 MB6-871덤프의 VCE테스트프로그램과 PMI-100덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 000-783시험에 대비한 고품질 덤프와 00M-503시험 최신버전덤프를 제공해드립니다. 최고품질 HP2-K34시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기